Vehicles
60 not categorized PORSCHE 996T REAR SEALCan't find what you need? Try browsing the Accessories or Exploded Diagrams!<-- Try narrowing by car using the menu to the left.96410601402EQ This OEM cover sits low nearest the rear bumper. If you are removing the motor for maintenance, be sure to check and replace the engine covers / heat shields as necessary. We recommend purchasing a new seal, part # 96410622301 and plug, part # 96410623701 to complete the installation. Sold individually. 1 necessary per car.
$601.70
Make a selection 944185072 Please specify year of car when ordering. General Fitment944 1989-91944 1985-88 944 1982-85
$587.79
Make a selection 95532119900 Known as: radial shaft seal / radial shaft seal 90 x 52 x 15 output flange rear axle View/Change Diagram
$42.57
Make a selection 99350465901 This is the rubber insert for the optional roof spoiler that contains a 3rd brake light at the top of the rear windshield. The option was # m599. This rubber insert seals the 3rd brake light in. Sold individually. 1 needed per car. Please note: we also sell a complete roof spoiler assembly that includes the insert spoiler and third brake light, it is our part # 190044812. View/Change Diagram
From $53.90
Make a selection 9655592950001C This seal sits above the rear most rocker panel section just in front of the rear wheel well. It seals the side skirt / rocker panel, part # 96555919502g2x sold individually. Driver's side fitment. For 964 turbo look / 965 turbo. View/Change Diagram
From $19.80
Make a selection 64453190100 Door seal (on door) rear section. Left/right (2 per car). View/Change Diagram
From $13.00
Make a selection 96811691100 Does your Porsche's tach needle climb in high gears and not move the car like it should? Does your 968 make a grinding noise in neutral? Does it seem to lurch during acceleration after shifts? These are all typical clutch problems. We offer complete packages to help you do it right! All clutch packages include clutch disc pressure plate release bearing and the always forgotten needle bearing (the little bearing in the flywheel that ruins your drive tube when it goes bad), the pilot bearing and the rear main seal. View/Change Diagram
From $827.84
Make a selection 99905305502 High quality sealed angular contact bearing. This number is superseded from 999 053 055 00. Sold individually. Left or right side fitment. Please note: this is the rear bearing for all the models listed below. View/Change Diagram
From $120.99
Make a selection 99911303850 Rear wheel bearing seal. Sold each, 2 needed per car. View/Change Diagram
From $16.50
Make a selection 93050417001 This genuine one-piece seal is closest to the rear bumper, we recommend replacing this when removing the motor for maintenance. We recommend replacing both the small and large engine seals, the small is part # 91150411502 sold individually. 1 necessary per car. View/Change Diagram
From $224.40
Make a selection AA500A Our rubber kits are for the perfect restoration. Available only from Automobile Atlanta, this kit consists of everything we use in our restoration shop. General Fitment914 1970-76
$1,012.23
Make a selection BBI9974010001 Features
$1,895.00
Make a selection FSPOR9972SHDR Product details: General Fitment911 2009-12
From $2,995.00
Make a selection FVD33150020 This kit is complete and includes the front and rear monoball cartridges with press tools. Our weather sealed monoball cartridges are crafted in high carbon steel and 7075 t6 aircraft aluminum. They will positively locate the suspension arms so suspension motion is accurately repeated in every corner. Sold as a set of 4. 1 kit is necessary per car. Please note: noise may resonate inside the cabin during street use.
$715.00
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection 99970203450 Fit 356 b/c cars this grommet protects the single wire at the rear corner of the light body it seals and saves the light from moisture View/Change Diagram
$1.10
Make a selection FVD500964965 This kit contains everything necessary to transform your narrow body c2 or c4 into a 965 wide body / turbo look. It includes motorsport quality glass-reinforced plastic (grp) front + rear bumper and side skirts along with metal fender flares. General Fitment911 1989-94
$7,353.98
Make a selection FVD500911RSR Made in europe by one of the manufacturers to Porsche. Extremely high-quality grp (glass-reinforced plastic) body kit that includes every detail for a perfect fit. This kit is not motorsports quality, it is OEM quality that sets it apart from the competition. Each part includes all the correct mounting cut outs, pre-drilled holes and fits like an OEM part for a perfect street car appearance. Features: - produced by an OEM manufacturer. - highest quality standards. - perfect fitment. - lightweight - made of high strength, grp (glass-reinforced plastic) kit contains: qty. 1 front bumper with spoiler, part # 10050305502 qty. 1 front bumper mounting kit, part # 10050305502mk qty. 1 rear bumper, part # 10050305503gf...(choose a part on the right to read more) General Fitment911 1970-73
From $9,222.99
Make a selection FVD545964000 This rear window is a high-quality lightweight replacement that is designed to perform like the original. It is a replacement for original number, 964 545 107 04. Features: 10 % lighter than original (weighs approx. 6 kg (13.2 lbs)) uses the original seal, part # 96454522500 clean appearance - does not include a cut out rear windshield wiper does not include a rear window defroster grid (less wiring / weight) green tinted, curved design like the original made in Germany please note: be sure to check the model fitment tab to ensure this works on your car.
$744.70
Make a selection MIT1409 Our front and rear stock fiberglass bumpers incorporate both the face bar and rubber top seal into one piece, facilitating installation and saving hundreds over the originals. please keep in mind that fiberglass does not provide the crash protection of steel, but saves weight for autocross and track events! For bumper with oil cooler cut out, use b91450590100. General Fitment914 1970-76
$395.00
Make a selection PLE54109900SEGR Trying to save weight at the track? These makrolon polycarbonate race windows are very lightweight, strong and durable. They are made in Germany. Includes right and left rear quarter windows and the rear windshield. Does not include the seals.
$2,087.80
Make a selection 639630 Finally, brake bleeding can be accomplished by one person! These speed bleeders are available to fit virtually any hydraulic brake or clutch system and uses OEM style sealing area to guarantee a positive leak-proof seal. Speed bleeders permanently replace original bleeder screw and come 2 per package with dust protection caps. General Fitment911 1989-94928 1987-91 944 1989-91
$15.24
Make a selection 90150509420
View/Change Diagram
From $14.69
Make a selection 90134116501 This is designed to perform like the original. Sold individually. 2 necessary per car. View/Change Diagram
From $26.20
Make a selection 90150549720
View/Change Diagram
From $11.50
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |